GO Faster Go Further
Established since 2001
Secure Supplies Group
9XB Stanley Meyer
NEW Board !
We have merged the scr to the 8xa as a easier option for builder , this means fast instill and replacement of parts . The boards can be ordered fully assembled.
Features:
* Official name 9XB
* Design based on the original Meyer circuit (it is the same schematic)
* Auxiliary power input for 9v battery
* Optocoupled output (H11D1)
* Additional output for panel led
* Additional output of + 5vcc
* Ready to connect power amp (used with VIC 8XA - SCR)
Modifications and implementations that can be made:
(by hydrogen hot rodders )
* HI-LOW frequency selector, since with this I can go through a greater frequency range (inverter key with 2 capacitors in the timer part).
* Incorporation of 12v + 12v x 300ma transformer
* Panel LED
installation * Interconnection terminal block installation for power stage
* Integral installation in acrylic and aluminum front for racking
* Installation of 1K potentiometer in series with the main (fine adjustment )
Signal generator (9XB)
This Board now INcludes the 9xd Voltage Regulator.
and is used with the 8XA VIC Voltage intensifier cicuit.
this is meyers circuit, he used it in the 8xa and the basic circuit is in most of his research
SUGGEST YOU DOWNLOAD ALL ON THIS PAGE AND PRINT IT OUT
This simple circuit operates from 1 Hz to about 12,4 kHz. It maintains 50% duty cycle. It was built by stanley to operate with house power and frequency.
The circuit consist of: - 1 x 555 Timer - 1 x 74LS04 - 1 x H11D1 - 1 x DIP selector switch - 1 x 7805 voltage regulator - 1 x 100 Kohm potentiometer - 1 x FWBR - 3 x 74LS90 - 2 x 220 ohm resistor - 2 x 4,7 Kohm resistor - 1 x 1 Kohm resistor - 1 x 10 Mohm resistor - 1 x LED - 3 x 1000 UF cap - 1 x 330 UF cap - 2 x 10nF cap (non polarized)
9XA Has the 9XD Power Supply Built in
Strongly Suggest you down load this video to you pc and
than re up load to other video streaming sites
AND SHARE TO YUR BUILDER CLUB
DO IT NOW
Parts and demo
https://www.youtube.com/watch?v=XkIvT2UPBAU
Don gabel and his 8xa demo
https://www.youtube.com/watch?v=wbeHmHEQYZU
9xd power supply
https://www.youtube.com/watch?v=VxFV0uDCeHg
how to assemble the 9xb( 8xa)
https://www.youtube.com/watch?v=XkIvT2UPBAU
the SCR board
https://www.youtube.com/watch?v=-yPH7rvO35Q
how a variac works
https://www.youtube.com/watch?v=bew6SuA4KEY
don gabel shows his 8xa
https://www.youtube.com/watch?v=wbeHmHEQYZU
me plating with my 8xa
https://www.youtube.com/watch?v=qOfyy9tWQ-U
how a transformer works............funny
https://www.youtube.com/watch?v=r14Am3kUigM
the 9xb and 9xa board
https://www.youtube.com/watch?v=9lZE9CYCzIc
my first board
https://www.youtube.com/watch?v=X5-WO5s0J98
the 8xa wave form...........my first time to understand it
https://www.youtube.com/watch?v=jC3X98TJuBY
Learning alot......8xa and distilled water
https://www.youtube.com/watch?v=R_HKcXELp2Q
the 555 timer is what makes the clock pulse. this is based off the meyer 555 arangment. you can see the signal that comes off the 555. the pot turns to speed up or slow down the. in this circuit, you can choose the speed of the frequency (meyers circuit only contains one freqency selection) , by the dip switch selection and then fine tune it with the potentiometer. this frequency output, then goes into the divide by 10...7490 chip
the meyer circuit, then goes ninto nthe 7490, as a devide by 10. this is a ripple counter. most any frequency input will be counted and for every 10 ripples in, one square wave 50% duty cycle will be output
so if you use multiple divide by 10.... you can divide 10khz to 1khz to 100hz.... like that. which is what meyer did
now you can take that same 7490 chip and devide by say 5 or 2 this is a devide by 2 diagram
so if you use multiple divide by 10.... you can divide 10khz to 1khz to 100hz.... like that. which is what meyer did
now you can take that same 7490 chip and devide by say 5 or 2 this is a devide by 2 diagram
now the 7404 is an invert chip. simply when you input an on, the chip says its an off. when you input an off, the chip says its a on. a 7414 is the same pinout. and funtions simularly, but different.....i suggest you look into some of this
Notes
The 5 volt regulator is power for the circuit only. it is a 7805 voltage regulator. the 05 shows its 5 volts. you can input 7 to 37 volts. 2 volts are lost in the regulator. at 7 volts no heat sink should be needed. at 37 volts, the extra voltage is disapated in heat, and a heat sink and fan are needed. you can pass 1.5 amps though this regulator. use a heat sink to do that.
SCR HOW MUCH AMPERS and voltS can release and at which frequency max ,min
the circuit was designed for 120 hz.........the circuit is a gate( on or off ) of rectified house power. 120 hz pulsed DC the circuit here can handle up to 6 amps. meyer used a 5 amp variac, so 140 volt and 5 amps maximum power i am not sure how fast of frequency it would handle. an scr is made to chop pulsed DC
usa house frequency is 60 hz rectify that.......it becomes 120 hz pulsed dc the 9xb is made to on and off the 120 hz............its an scr..........it turns pulsed freqency on and off. there has to be an of time for the scr to function. say on for 10 pulse off for 10 pulses..........it will not make 5khz pulses from pulsed dc of 120 hz its a gate function the rectified house power is the main frequency
60 hz AC full wave rectification, becomes 120 hz pulsed DC
What is the biggest constant in the universe -no MAN can change TIME LINE -It is just an illusion and if you cut off the signal with 120hz or 50/50 meaning current which is at the entrance(watts) you only 50% get out which means VFC works with 50% of power with alternator you roughly have 500-1000 hz true and pure oscillations-and we all know what that means and Meyer constantly mentions 5000hz or 5khz
the vic transformers work on the design of the coil and perm of the core. he set them to match 5 khz, which is the midpoint that his circuit would pulse at. the variac circuit was different that it worked at 120 hz, that was his first test unit i think. then the alternator, then the more complex circuits
9xa There is only used 50% of enrgy from variac-but it is not important now that will explain later I presume you've got a small hho gas production also you applying a significant amount of energies for this process but what it means apply-it's like a normal capacitor when is full you have a big energy between tiles ,you have great energy but it is not spending my question is, you can prove it with 9xa you do not need any extra equipment(this can be easily done later)if we are right). and here is not important quantities of gas and time.It is important current consumption right away measure from the outlet and the amount of gas produced I guess you spend a couple of watts and the amount of gas will be small , but will also be a great In response to consumed wats and if is accurate then only needs to boost system with his electronics and stuff-Only then we will get the true extent of consumption production what I mean hi has efficiency only at high energy levels
1n4005 diode should be ok picture of your cell please its my opinion that all test with Meyers cells should be made with rain AND city water either or, one then the other meyer lived in grove city, a suberb of Columbus, the capital city of the state. his tap water was treated city water. over and over we see him fill it from the garden hose if your cell is too small and just one tube set, I will say it will heat up I also think at proper resonate action , a completely different process will take over
the size of the vessel if there is no water flow, you turn it into the meyer heater
So the two wires go in and are bifilarly wound and then they come out... Are the two "beginning wire ends" hooked up to the pos and meg on the scr, or is one hooked upto the cell and the other to the scr. talking about the inductors for the Ecore's The wiring up of them, one start hotwire to the cell and one negative finish to cell?
Circuit Pictured Below Showing Bifilar wind and connections.
Part 1N1188 blocking diode must go between bifilar choke and cell to hold the voltage in the cell like a capcitor. and protect your scr and bifilar choke.
Description Silicon Standard Recovery Diode, cell is un grounded.
Feature 1N1188; Silicon Standard Recovery Diode Features • High Surge Capability
• Types from 400 to 600 V VRRM • No.
Stanley Meyer How to makes Chokes 8XA 9XA 9XB Etc #hho #hydrogen#stanleymeyer https://t.co/aam8UCqNnv GET THE FULL DOC NOW
Using 9xb in Flip Flop
This is how flip - flop circuit works with Stanley Meyer 9xb circuit and activates three relays This board has two components: Microchip CD4013BC - 2 Resistor 4,7 K - 1
Using 2x 9xb to make a 9xa
This is how flip - flop circuit works with Stanley Meyer 9xb circuit and activates three relays This board has two components: Microchip CD4013BC - 2 Resistor 4,7 K - 1
Stanley A Meyer 9xb WFC BUILDS GLOBALLY
Stanley Meyer's 8XA Hydrogen Fracturing Process
•04 October 2022
Input: 220 Volts / 50 Hz Half-wave unipolar frequency next the Graetz -
100 Hz Gate frequency to the Optocoupler`s input
- 51Hz (or 49 Hz) / 50% Duty-cycle Anode Inductor C1
- 400 turns Cathode Inductor C2
- 404 turns* How to "fine tune" the Cathode inductor "L2":
If "L2" have exactly 400 turns /like L1/
- the Waveform is "most Positive":
If "L2" have 410 turns /10 turns more/ - the Waveform is "non symmetrical" - the Negative voltage outweighs the Positive voltage:
https://www.nikola-truck.com/product-page/9xd-9xb-scr-3-in-1-pcb-only