You can produce your own Hydrogen from electricity using either common "household current" or directly from solar cells so your energy cost is zero. It does however take a substantial amount of time to produce sufficient Hydrogen to fill even a small tank.

   As an example, it takes over 2 days of our generator running at full power, 24 hours a day, to fill our smallest "short range" tank.

​

Storage

There are but 4 ways to do this:

​

1. Store the Hydrogen as a compressed gas.
2. Store the Hydrogen as a liquid.
3. Store the Hydrogen chemically bonded to a chemical.

4  Make it on demand as a gas and remove electrons or keep gas positive charged

5  Make it on demand and have is stored in water as a nano bubble suspension. 

​

We'll cover each option in order.

​

1.Compressed Gas 

If you choose to store the Hydrogen as a compressed gas, you'll need ,multiple or larger tanks, or higher storage pressures. The Standard is 300 to 600 Bar depending on application.

​

2. Choosing liquid

does solve the density problem since liquids are far more dense than gasses, so you can reduce the amount of tanks and their sizes required to power the car.

The liquid Hydrogen is cryogenic in short very cold.

It requires vacuum-thermos ( dewar ) tanks and vents to exhaust the boiling Hydrogen gas.

You'll also have to find a source for liquid Hydrogen which is far more expensive than Gasoline due to compression.

​

3. There are materials call Hydrides

that absorb Hydrogen like a sponge absorbs water. Typically, the tanks are filled with granulated Hydrides, and Hydrogen is pressurized into the material. Hydrides have many advantages over liquid & gas. One is that the density of the Hydrogen stored in the Hydride can be GREATER than that of liquid Hydrogen. This translates directly into smaller and fewer storage tanks.

Once the Hydride is "charged" with Hydrogen, the Hydrogen becomes chemically bonded to the chemical. Even opening the tank, or cutting it in half will not release the Hydrogen gas. In addition, you could even fire incendiary bullets through the tank and the Hydride would only smolder like a cigarette. It is in fact, a safer storage system than your Gasoline tank is.

Then how do you get the Hydrogen back out? To release the Hydrogen gas from the Hydride, it simply needs to be heated. This is either done electrically, using the waste exhaust heat, or using the waste radiator coolant heat.

​

The Corvette  above heated the Hydride tanks electrically, and as soon at the Hydride is sufficiently warm, Hydrogen is released from the tanks and the on-board computer detects the presence of Hydrogen pressure. The fuel system remains in "Hydrogen" mode until the tank pressure begins to drop. If the tanks run out of Hydrogen, the engine will seamlessly switch over to Gasoline, which enables the car to run conventionally until the Hydrogen tanks are refilled.

​

4. It is possible to make a GTNT gas

a gas that is a positive charge missing electrons,(avoids and prevent water reforming until combusted ) in this case the engine is positive earthed to act as a electron sink. And or you can remove electrons and avoid ground back by reducing negative surfaces and ambient air contract. In that case all incoming air is gated with a diaphragm control intake  and  restricted air flow in and processed to be positive charged before rising with positive charged fuels.  On demand as a gas and remove electrons or keep gas positive charged this ways instead of implosion you get explosive force with out heat. 2 x hho we cut the power of this fuel with positive charged EGR gas.

​

​

5.Water Fuel Suspensions 

Make it on demand and have is stored in water as a nano bubble suspension.

This method is cutting edge and possibly the final solution to the world problems we use out knowledge in all of the above to control the charge temperature of water to hold dissolved h2 gas , so instead of 2 to1 h2 to 02 we have 10 to 1 or any mix we like until saturated.

​

Using Hydrogen,

the only exhaust products produced are water vapor and a tiny amount of Nitrogen Oxides.

Which can be processed in a egr gas processor to ensure break up of nitrogen and the positive charge.

It's about as clean burning as you can get.

​

To Study this please Join and Support the Parts Training Guide.

​

​

​

​

​

​