top of page

Stanley Meyers Multi VIC Arrays

Page as a Pdf.png
Stanley A Meyer Voltage intensifier Circ
1508500977868.png

The Above Board is controlled by the tps throttle position it will simply taking the db9 coming out from the matrix main board and split to 10 db 9 to each vic card on each vic transformer going into the vic daughter board.

the sequential tps Trigger go out to a vps vic power switch board shown below each board runs 2 vic so you have 5 of these boards and 10 vics triggered on off from throttle position it has a fine tune resistor for sensitivity

Stanley A Meyer Vic Array Power Switch.j
Stanley A Meyer Sequential Vic Switch
Stanley A Meyer Sequential Vic Switch
Stanley A Meyer Multi Vic  1.png
Stanley A Meyer Vic Parallel.png
Stanley Meyer Multi Array VIC  version circuits
Stanley A Meyer VIC Parallel 10

Note

50% AND adjustible Pulse with
I made that mistake on the rustic custom. But using mosfets as well. Another nono

Parallel  10 Vic 

Stanley A Meyer Multi Vic.png
Stanley A Meyer Home Heater Unit Steam R
Stanley A Meyer Muitl Parallel Vic Array
Stanley A Meyer VIC Multi
53845617_10156242018850098_3033579334385
Main part of the step charging circuit that people have
\ missed. Everybody thinks that step charging is an effect that
 happens, but it's not. Voltage doubling is real in each vic but the 
 Step charging was a forced oscillation. meaning yes we get voltage doubling we get LMD oscillation and cell charging , but in additional we can magnify oscillations with trigger time parallel vics if it sounds like a  very powerful fuel on demand maker it is..
THANK YOU HYDROGEN HOT RODDERS
Stanley A Meyer VIC Multi

Apparently, the connection "in parallel" is preferably, but you must
 try "two ways".

Edward Mitchell's Website:
 http://aetherforce.com/inventors-diary-failing-to-learn-making-good-use-of-the-scientific-method/

Edward Mitchell's Two Big bobbins in oil:
https://www.youtube.com/watch?v=RWhQusfWuac
===========================================================
My Circuit diagram: http://alfa.kachi-snimka.info/images-...

Copper wire: https://static2.tme.eu/products_pics/0/1/2/0120ec28bc96b5b1ce1ba1999ce204b0/18213.jpg

 High voltage Teflon insulation tape - Russia's Military production,
 60 ?V/mm. (One Layer 0,08 mm. = 4,8 kV):
http://www.pentod.com/product/44/teflonova-lenta-izolatsionna-0-08mm-h-100-mm.html
 (Here, I use two layers - 0,16 mm. = 9,6 kV)

==========================================================

Stanley Meyer's Memo WFC 420: http://www.sentex.ca/~mec1995/hho/Meyer/Stan_Meyer_Full_Data.pdf

In Memo WFC 420 (Page 1-3) Stanley Meyer say:
"Voltage intensity or level across Excitor-Array (ER) can exceed 20,000 volts"
. Stanley Meyer's Memo WFC 426: http://www.sentex.ca/~mec1995/hho/Meyer/Stan_Meyer_Full_Data.pdf

In Memo WFC 426 (Page 7-1) Stanley Meyer say: "The "mode-of-operability"
of VIC Coil Assembly allows Voltage Potential of opposite voltage polarity
 to increase and be attenuated up to and beyond
 20 Kilovolts while inhibiting and restricting amp leakage
 in the milliamperes range ..." Canadian Patent 2,067,735:

 http://www.rexresearch.com/meyerhy/2067735.htm
=======================================================

 In Canadian Patent 2,067,735 Stanley Meyer say:
 "Ionized air gases and non-combustible gases,
introduced through nozzles 2A1 and 3A1,
 are intermixed with the expelling water mist to form

a fuel-mixture which enters into voltage zone 6 where
the mixture is exposed to a pulsating, unipolar high intensity
 voltage field (typically 20,000 volts at 50 KHz or
above at the resonant condition in which current flow
in the circuit [amps] is reduced to a minimum),
created between electrodes 7 and 8." Stanley Meyer's

http://www.rexresearch.com/meyerhy/2067735.htm
======================================================================
 In Memo WFC 425 (Page 6-2) Stanley Meyer say:

"All activation points (E9a - b - c - d) performing
their respective functions in sequential order in an
 instant of time since applied voltage level of intensity
(typically 20,000 input volts or so) can be extended or
 increased up to and beyond 90,000 volts range within
 a millisecond or less".

http://waterpoweredcar.com/pdf.files/section6.pdf

Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit

Techniques and parts which may provide build tips

Aliens made me do it 

Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
Stanley A Meyer Muilt Parallel VIC Sync Circuit
bottom of page