top of page

Estate photographs were used in conjunction with a pair of calipers. Screen was adjusted until a common reference point was ascertained. The reference point used was the known dimensions of the LED PCB width, being 1.00". Length was determined by laying out the number of 5mm LEDs (16-qty) in a PCB CAD software. The distance from the first to the last was exactly 4.00". When the screw terminal via holes are added, the board length becomes 4.75" long. This is what decided the length of the acrylic body. 

Page as a Pdf.png
Stanley A Meyer Gas Gun Ionization system JET (7).png
Stanley A Meyer Gas Gun Ionization system JET (20).png

ACRYLIC PHOTON INJECTION BODY:

IMG_8911.JPG

Acrylic "photon injection" diameter: 2.75"  (note that flat spots were intentionally done on the 3D prints to allow for LED PCBs. It was found that a square of equal sides, 2.75" with .875" radius on each corner produced the desired outer diameter and provided 1" wide flat surfaces for PCB mounting). A 0.375" depth was chosen based off dimensions of 5mm LEDs for the grooved portion. 

 

ACRYLIC BOBBINS:

Top and bottom bobbin end appear to have some type of mounting holes that appear to line up with holes on the end caps. These were determined to the closest approximate of 2.125" on centers. This was included in STL designs.

Stanley A Meyer Gas Gun Ionization system JET (5).png
Stanley A Meyer Gas Gun Ionization system JET (15).png
REPLICATION BREAKDOWN:

 The photo injection body is meant to be printed in PLA/PETG as this shouldn't be required to be clear, as only in inner chamber has light pulsed. There are two pieces. One top and one bottom. There was intentionally a shorter section on the bottom (1a) and a longer section on the top (1b). This is functioning as a keying to avoid mistakes in assembly. These two section need to be glued at their center junction. The larger diameter seen is for a acrylic resin cast from a mast mold. 

Stanley A Meyer Gas Gun Ionization system JET (19).png
Stanley A Meyer Gas Gun Ionization system JET (21).png
ACRYLIC LENS:

Having solid piece of acrylic machined is costly and difficult to source for only one piece. These hurdles inspired the idea of 3D printing a mold template. There is a hole provided for tapping a 10-32 screw connection into outer electrode. Once cured, the lens is inserted coaxially to the inner/outer electrode. For best results, the silicone mold and acrylic resin should be placed inside vacuum chamber to remove air bubbles during curing. Gluing is not intended for this piece.

Inner Diameter: 1.025"

Outer Diameter: 1.980"

Length is 4.50"

Stanley A Meyer Gas Gun Ionization system JET (8).png
Stanley A Meyer Gas Gun Ionization system JET (6).png
PHOTON BODY END PLATES:

 In order to secure the acrylic lens, and provide a gluing surface for coil bobbins, two "end caps" are to be glued into place on each end of the body. This brings the total length to 4.75".

Stanley A Meyer Gas Gun Ionization system JET (4).png
OUTER ELECTRODE:

 Outer electrode is T-304 stainless steel tube. 7.00" in length, 1.00" outside diameter, 0.94" inside diameter, 0.030" wall. Grooves are cut at 90 degree displacements, measuring 4.00" long. 

Stanley A Meyer Gas Gun Ionization system JET (11).png
Stanley A Meyer Gas Gun Ionization system JET (2).png
OUTER ELECTRODE STENCIL:

 Being that the machining required to cut grooves in the tubing is costly, for only one piece, an stencil to go over the body for marking grooves was made. The intention was to cut the grooves with Dremel cutting wheel. 

INNER ELECTRODE:

Stanley A Meyer Gas Gun Ionization system JET (12).png
Stanley A Meyer Gas Gun Ionization system JET (3).png
BODY TOP END BOBBIN HALF PIECE:

Glue the 0.25" thick bobbin to the top via the 1.30" surface. This will complete the top bobbin for coil.

BODY BOTTOM BOBBIN HALF PIECE:

At the bottom of the body, glue a .125" thick bobbin half piece to the corresponding 1.30" diameter surface. 

Next, glue another .125" thick bobbin half piece to the 2.75" surface. 

Next, glue last .25" bobbin half piece the 1.30" surface.

COMPLETE ASSEMBLY:

Following the steps above will yield a completed assembly.

INSERT OUTER ELECTRODE:

Press fit in the 1" outer electrode, aligning the grooves in the tube with the grooves in the plastic body.

BOTTOM END CAP:

The bottom end cap has recessions on the bottom to receive wiring. Terminals are 8-32" brass screws. Inner electrode should be press fitted like shown. 

Insert the inner electrode so it is coaxial to the inside of the outer electrode.

TOP END CAP:

Repeat the same step for top end cap that was done for the bottom be inserting inner electrode into middle support.

INSTALLING TOP/BOTTOM CAPS:

Top cap goes on top of the "top end cap". 

Bottom cap goes onto the bottom end cap. 2.125" holes line up for securing through "bottom end cap" and bottom 0.25" wall coil bobbin. When installing this one, make sure the four holes on the side match the four holes on the inside.

COMPLETE UNIT:

This is what the entire unit should look like once completed. 

See ORIGINAL HYDROGEN GAS GUN:

Stanley A Meyer Gas Gun Ionization system JET (10).png
Stanley A Meyer Gas Gun Ionization system JET (22).png
Stanley A Meyer Gas Gun Ionization system JET (16).png
Stanley A Meyer Gas Gun Ionization system JET (9).png
Stanley A Meyer Gas Gun Ionization system JET (17).png
Stanley A Meyer Gas Gun Ionization system JET (13).png
Stanley A Meyer Gas Gun Ionization system JET (14).png
Stanley A Meyer Gas Gun Ionization system JET (18).png
Stanley A Meyer Gas Gun Ionization system JET (1).png

Stanley Meyer Told the Truth 

Finally you in the right place to learn the correct terms of this unit.

A Plasma Pinch is a common item and technique in  Atomic Research.

Here you can find correct terms and  description of this device , 

This device can be used to make plasmoids and  pinch  ionised and bond gases.

Study and Study Hard. 

We can not the only way we join the this and discover thed the theory was from Joe Cell

his rather pure explanation gave us hints to way Stan was looking at and the fact Stan work at a nuclear  company gives us the tip.

Now you know this and the terms for it  there is a wealth of  knowledge decades to read on the subject.

The Coils in Stans Device are the Pinches and the  Z Ionization occurs on the tubes and the laser raising energy levels is from Stanley Meyer Stan Told the Truth.

https://patentimages.storage.googleapis.com/7f/28/18/e776d9c8ae8945/US20060180473A1.pdf

 

6a00d8341c4fbe53ef01b7c6e53158970b-800wi
45-breakthrough.jpg
plasma-clipart-force-field-188516-592300
Stanley A Meyer Gas Gun.jpg
bottom of page